Numerical Methods
EEE · Midterm · Summer 26
Batch 242
Read the questions as text
Read off the PDF by AI, so it may have mistakes. The PDF is the original.
Daffodil International University
Department of Electrical and Electronic Engineering
Faculty of Engineering
Midterm Examination, Summer - 2026
Course Code: 0541-213
Course Title: Numerical Methods
Teacher's Initial: AKB, SP
Section: A, B, C, D, E
Level-Term: L3-T1
Time: 1.5 Hours
Full Marks: 25
Exam Date: July 01, 2026
[Answer any Five of the Six Questions given below. The second rightmost column indicates the COs (course learning outcomes of the course) with respective Bloom's level, and the rightmost column indicates the assigned marks.]
Q1. The current passing through an electric device is given by the equation: I(t) = t^2, where t is the time in seconds and I is the current in amperes. The voltage across the device is given by: V(t) = t^2 - 9t + 26 + (96/t). Hence, the power dissipated in the device is: P(t) = V(t)I(t). Using the "False Position Method", determine the value of time t at which the power dissipated is 120 W. Take the initial guesses as a = 2.5 s and b = 3.75 s. Stop the iterations when the absolute difference between two successive approximations of t is less than 0.01 s. CO-1 C(3) [5]
Q2. A cylindrical conductor is designed such that its resistance depends on its length. The volume of the conductor is fixed at 500 cubic centimeters, and the radius of its cross-section is equal to the square of its length. Using an iterative method, determine the length of the conductor. Start with an initial guess of L_0 = 4 cm and perform iterations using the "Newton-Raphson Formula". Stop when the error in the solution, measured by the value of the difference between the calculated and desired volume, is less than 0.5. CO-1 C(3) [5]
Q3. The mesh equations of an electric circuit are given below:
2I_1 + 8I_2 + 2I_3 = 0
4I_1 + 2I_2 = 4
2I_3 + 4I_4 = 0
2I_2 + 8I_3 + 2I_4 = 0
Using the initial approximation: I_1^(0) = 0, I_2^(0) = 0, I_3^(0) = 0, I_4^(0) = 0, perform three (3) iterations of the "Gauss-Seidal Method" to solve for the mesh currents I_1, I_2, I_3, I_4. During the calculations, retain values up to four decimal places at each step and round off accordingly. CO-1 C(3) [5]
Q4. For the circuit shown in Fig. 1, write the nodal equations for the node voltages v_1, v_2, and v_3. Then solve the resulting simultaneous linear equations using the "Gauss-Jordan Method". CO-1 C(4) [5]
[Figure: A circuit diagram showing a DC current source of 5 A connected in parallel with an 8 ohm resistor and nodes v_1, v_2, v_3 connected through 2 ohm, 4 ohm, and 8 ohm resistors, controlled by a 3 A current source at the top and a 12 V voltage source at the bottom right.]
Q5. The capacitance values (in uF) of capacitors, measured in a quality-control test, are given in Table 1. CO-1 C(3) [5]
Table 1: Distribution of Capacitance Values
Capacitance (uF) | 35-45 | 45-55 | 55-65 | 65-75 | 75-85
Number of Capacitors | 20 | 40 | 60 | 60 | 20
Estimate the number of capacitors whose capacitance lies between 42-55 uF.
Q6. An AI company provides an NLP-based text summarization service. The service uses GPU processing time to generate summaries from large text documents. The relationship between GPU processing time and the number of summaries generated is given in Table 2. CO-1 C(3) [5]
Table 2: GPU Processing Time vs. No. of Summaries Generated
GPU Processing Time (minutes) | 40 | 60 | 90 | 120
No. of Summaries Generated | 18 | 27 | 43 | 55
The cost of GPU processing is Tk.12 per minute, and the company charges Tk.30 for each generated summary. Using "Lagrange's Interpolation Formula", estimate the number of summaries generated when 100 minutes of GPU processing time is used. Hence, determine the profit or loss incurred by the company for using 100 minutes of GPU processing time.