Electrical Circuits I
EEE · Final · Summer 26
Read the questions as text
Read off the PDF by AI, so it may have mistakes. The PDF is the original.
Daffodil International University
Department of Electrical and Electronic Engineering
Faculty of Engineering
Final Examination, Summer - 2026
Course Code: 0713-111
Course Title: Electrical Circuits I
Teacher's Initial: MRK, KAH
Section: A, B, C, D, E, F
Level-Term: L1-T1
Full Marks: 40
Exam Date: August 27, 2026
Time: 2 Hours
Answer all questions below. The second right column indicates the course outcomes (COs) with respective Bloom's level and the right column indicates the allocated marks.
Q1. a) State Superposition theorem. Obtain i in the circuit of Fig. 1 using superposition theorem. CO2 [05] C(3)
[Figure: Circuit diagram containing a 2 A current source, a 20 V voltage source, and several resistors (5 ohm, 10 ohm, 4 ohm, 5 ohm) labeled Fig. 1]
b) State Thevenin theorem. Determine Vo in the circuit of Fig. 2 applying Thevenin theorem. CO2 [05] C(3)
[Figure: Circuit diagram containing a 3 A current source, a 12 V voltage source, and several resistors (4 ohm, 16 ohm, 5 ohm, 1 ohm, 10 ohm) labeled Fig. 2]
Q2. a) State maximum power transfer theorem. Show that the maximum power transfer takes place when the load resistance equals the Thevenin resistance of the circuit. CO2 [05] C(2)
b) Determine the value of RL that will draw the maximum power from the rest of the circuit shown in Fig. 3. Calculate the maximum power. CO2 [05] C(3)
[Figure: Circuit diagram containing a 12 V voltage source, a 2 A current source, resistors (6 ohm, 12 ohm, 3 ohm, 2 ohm) and load resistor RL labeled Fig. 3]
Q3. a) Analyze the transient behavior of a 1st order RC series circuit during charging phase and sketch the transient voltage and current up to five-time constants of that network during this phase. CO3 [04] C(4)
b) For the circuit of Fig. 4:
i. Determine the time constant of the circuit when the switch is thrown into position 1.
ii. Find the mathematical expression for the voltage across the capacitor after the switch is thrown into position 1.
iii. Determine the mathematical expression for the current following the closing of the switch at position 1.
iv. Obtain the voltage vc and the current ic if the switch is thrown from position 1 into position 2 at t = 100 ms.
v. Determine the mathematical expressions for the volt age vc and the current ic if the switch is thrown into position 3 at t = 200 ms.
vi. Plot the waveforms of vc and ic for a period of time extending from t = 0 to t = 300 ms.
CO3 [06] C(4)
[Figure: RC circuit diagram with a 50 V source, resistor R1 (3 kohm), capacitor (2 uF), resistor R2 (2 kohm), and a multi-position switch connected to nodes 1, 2, 3, labeled Fig. 4]
Q4. a) Describe Hysteresis behaviour of the magnetic material with sketching if any. CO1 [05] C(2)
b) Obtain the current I required to establish a flux 3 x 10^-4 Wb in the magnetic circuit of Fig. 5. Also find mu and mu_r for Sheet steel and Cast iron both. CO2 [05] C(3)
[Figure: Diagram of a magnetic core with a coil of N turns carrying current I, with indicated Cast iron and Sheet steel sections, l_iron core = l_steel core = 0.3 m, Area = 5 x 10^-4 m^2, N = 100 turns, labeled Fig. 5]