Skip to content

Basic Electrical and Electronic Engineering

TE · Final · Spring 26

Paper 2 of 2By Ahnab ShariarSwitch

Paper 2 of 2

This browser can’t show the PDF here

Open it, and your phone’s PDF viewer takes it, or download it.

Read the questions as text

Read off the PDF by AI, so it may have mistakes. The PDF is the original.

Daffodil International University Department of Textile Engineering (TE) Faculty of Engineering Final Examination, Spring-2026 Course Code: 0713-221 Course Title: Basic Electrical and Electronic Engineering Level & Term: L2T2 Full Marks: 40, Time: 2 Hours Course Teacher: Tasnia Noshin Orin (TNO), Amit Kumar Paul (AKP), Sakaid Hosain Shakir (SHS) (Answer any 5 set of the following Questions) 1. a. Explain whether you can apply mesh analysis for the given circuit or not and find the currents. [CLO-2, C2, C1] [4+4] [Figure: Circuit diagram with a 20 V source, 6 ohm resistor, R2 = 4 ohm resistor, R3 = 2 ohm resistor, 4 A current source, and a 12 V source] b. Find current i1, i2, i3, i4 [Figure: Circuit diagram for mesh analysis with four loops showing currents i1, i2, i3, i4, resistors, and sources including 5 A and 10 V] 2. a. List steps to determine node voltages. [CLO-2, C1, C5, C2] [2+3+3] b. Determine node voltages at three non-reference nodes. [Figure: Circuit diagram with a 4 A current source, 3 ohm resistor, 2 ohm resistor, 4 ohm resistor, 6 ohm resistor, and a dependent source 4Ix] c. Calculate the unknown node voltages. [Figure: Circuit diagram with 2 A current source, R1 = 6 ohm, 3 ohm resistor, 3 A current source, and R2 = 4 ohm] 3. a. Define: Zenner breakdown, Avalanche breakdown. [CLO-4 C1, C2, C3] [2+4+2] b. Explain V-I characteristics curve of PN junction diode with proper diagram. c. Suppose you have a silicon diode with a reverse saturation current (1.5x10^-12A). Calculate the diode current if the knee voltage is 0.67V and n=1.5 at room temperature? 4. a. Determine the current Io of the following circuit 4.1 [CLO-3, C5] [4+4] [Figure: Fig 4.1, a circuit with 24 V source, resistors 10 ohm, 12 ohm, 4 ohm, 24 ohm, and a 4 A current source] b. For the following circuit 4.2 find Io when Vs=12V & Vs=24V and determine whether the circuit is linear or not. [Figure: Fig 4.2, a circuit with Vs source, 6 ohm resistor, 2 ohm resistor, 4 ohm resistor, 8 ohm resistor, 4 ohm resistor, a 1 A current source, and a dependent source 3vx] 5. a. Determine V1 and V2 using Nodal analysis. [CLO-3, C5, C1] [4+4] b. Calculate the Current at 10 ohm and 20 ohm resistor. [Figure: Circuit diagram with 20 V source, 50 ohm resistor, V1 node, 10 ohm resistor, V2 node, 20 ohm resistor, 100 ohm resistor, and a 4 A current source, with node V3 at the bottom] 6. a. Identify the value of I1 and I2 when the 120 V source is deactivated. [CLO-3, C1, C5] [4+4] b. Determine I1 when the two voltage sources are both active in the circuit. [Figure: Circuit diagram with a 120 V source, 6 ohm resistor, 6 ohm resistor, 3 ohm resistor, 6 ohm resistor, 7 ohm resistor, and a 60 V source]