Skip to content

Energy Conversion II

EEE · Final · Summer 26

Paper 2 of 2Batch 251Switch

Batch 251

Paper 2 of 2

This browser can’t show the PDF here

Open it, and your phone’s PDF viewer takes it, or download it.

Read the questions as text

Read off the PDF by AI, so it may have mistakes. The PDF is the original.

Daffodil International University Department of Electrical and Electronic Engineering Faculty of Engineering Final Examination, Summer - 2026 Course Code: 0713-223 Course Title: Energy Conversion II Section: A, B, C, D Level-Term: L2-T2 Teacher's Initial: NR, RS Full Marks: 40 Exam Date: August 19, 2026 Time: 2 Hours Notes: Answer all the questions below. The second right most column indicates the course outcomes [COs] with respective Bloom's level and the right most column indicates the allocated marks. Q1. Explain the commutation process in a DC generator with necessary illustrative diagrams. | CO-1 C(2) | 5 Q2. Briefly describe the followings with necessary curve for series DC motor, | CO-1 C(2) | 5 (i) Torque versus Armature Current Characteristic (ii) Speed versus Torque Characteristic Q3. Analyze how variations in field current affect the operation of a synchronous motor, and justify your analysis using an appropriate phasor diagram. | CO-2 C(4) | 5 Q4. A d.c. shunt machine generates 250-V on open circuit at 1000 r.p.m. Effective armature resistance is 0.5 Ω, field resistance is 250 Ω, input to machine running as a motor on no load is 4 A at 250 V. Analyze the behavior of the machine by determining the speed as a motor taking 40 A at 250 V. Armature reaction weakens field by 4%. | CO-2 C(4) | 5 Q5. A 220-V compound generator is supplying a load of 100 A at 220 V. The resistances of its armature, shunt and series windings are 0.1 Ω, 50 Ω and 0.06 Ω respectively. Evaluate the induced e.m.f. and the armature current when the machine is connected (i) short shunt (ii) long shunt (iii) how will the series amp-turns be changed in long shunt if a divertor of 0.14 Ω is connected in parallel with the series windings? Neglect armature reaction and brush contact drop. | CO-3 C(5) | 5 Q6. A 4-pole, 250 V d.c. series motor takes 20 A and runs at 900 r.p.m. Each field coil has resistance of 0.025 ohm and the resistance of the armature is 0.1 ohm. Determine the speed that run the motor by developing the same torque if: | CO-3 C(5) | 5 (i) rearranging the field coils in two series and parallel groups Assume unsaturated magnetic operation. Q7. A 2300-V 1000-hp 0.8-PF leading 60-Hz two-pole Y-connected synchronous motor has a synchronous reactance of 2.8 Ω and an armature resistance of 0.4 Ω. At 60 Hz, its friction and windage losses are 24 kW, and its core losses are 18 kW. The field circuit has a dc voltage of 200 V, and the maximum IF is 10 A. Answer the following questions about the motor, assuming that it is being supplied by an infinite bus. | CO-3 C(5) | 5 (i) Evaluate IA and EA with angle if this machine operates at unity power factor when supplying full load. (ii) Determine the motor's efficiency at full load and unity power factor. (iii) If the flux were increased by 2.83 %, calculate the new armature current. Q8. A 75-kW, 3-ϕ, Y-connected, 50-Hz, 440-V cylindrical rotor synchronous motor operates at rated condition with 0.8 p.f. leading. The motor efficiency excluding field and stator losses is 95% and Xs = 2.5 Ω. | CO-3 C(5) | 5 Evaluate: i. mechanical power developed ii. armature current iii. back e.m.f. iv. power angle v. pull-out torque of the motor