Skip to content

Electronics I

EEE · Final · Summer 26

Paper 1 of 2By Ashik 152Switch

Paper 1 of 2

This browser can’t show the PDF here

Open it, and your phone’s PDF viewer takes it, or download it.

Read the questions as text

Read off the PDF by AI, so it may have mistakes. The PDF is the original.

Daffodil International University Department of Electrical and Electronic Engineering Faculty of Engineering Final Examination, Summer - 2026 Course Code: 0714-211 Course Title: Electronics I Teacher's Initial: SD, KNA, KAH, MH Section: A, B, C, D, E, F, G Level-Term: L2-T1 Time: 2.0 Hours Full Marks: 40 Exam Date: August 27, 2025 [Q1 and Q2 are mandatory; Answer any three (03) from questions Q3, Q4, Q5, Q6.] [The second right most column indicates the COs with respective Bloom's level.] [The right most column indicates the assigned marks.] [All the symbols carry their usual meaning.] Q1. (a) Write the names of BJT modes of operation and mention the biasing conditions of the junctions for each of the operating modes. CO1, C2 [2] (b) For a BJT, show that beta = alpha / (1 - alpha). CO1, C2 [2] (c) Explain the operation of an n-channel MOSFET with necessary diagrams. CO1, C2 [4] Q2. For the circuit of Fig. Q2, (i) Calculate the value of Rc if the collector voltage is 3.4V at dc operating point, (ii) Draw the small signal equivalent circuit, (iii) Derive the expressions and find values for Zi, Zo and Av. CO2, C3 [8] [Figure: Circuit diagram of BJT amplifier with Vcc=12V, Rb=400kΩ, Rc, Re=4kΩ, Cc1, Cc2, Cg, β=120, ro=50kΩ, Vc=3.4V] Q3. Given that VB = 4V for the following circuit of Fig. Q3, determine (i) VE, (ii) Vc, (iii) beta. CO2, C3 [8] [Figure: Circuit diagram of BJT voltage divider biased amplifier with Vcc=30V, Rf1=330kΩ, Rf2=220kΩ, Rc=8.2kΩ, Re=1.8kΩ, vb=4V, capacitors 10µF, 5µF] Q4. Given the device characteristics in Fig. Q4(b), determine R1, R2, Rc and Icsat for the circuit in Fig Q4(a). Assume beta = 150. CO2, C3 [8] [Figure: Circuit diagram Q4(a) and graph Q4(b) showing IC vs VCE with Q-point, 4mA, 12V] Q5. It is required to design the following circuit for biasing a MOS Amplifier. The design requirements are VDD = 5V, ID = 0.32mA, VS = 1.6V, VD = 3.4V with a 1µA current through Rg1 and Rg2. Assume Vt = 1V and kn' (W/L) = 1 mA/V^2. Determine the values of all the resistances in the circuit. CO2, C3 [8] [Figure: MOSFET biasing circuit with VDD, Rg1, Rg2, RD, RS] Q6. (a) Draw the small-signal ac equivalent circuit for the following Common-Source (CS) amplifier. CO2, C2 [4] [Figure: Common-source CS amplifier circuit with VDD, RD, RS, CS, Cc1, Cc2, Rsig, RL, Vsig] (b) The MOSFET in the following circuit of Fig. Q6(b) has Vt = 1V, kn' (W/L) = 0.4 mA/V^2 and lambda = 0. Determine the drain voltage. CO2, C3 [4] [Figure: MOSFET circuit Q6(b) with VDD = +5V, RD = 1kΩ, VD]