Skip to content

Electronics I

EEE · Final · Summer 26

Paper 2 of 2By Md. Golam Murshed HridoySwitch

Paper 2 of 2

This browser can’t show the PDF here

Open it, and your phone’s PDF viewer takes it, or download it.

Read the questions as text

Read off the PDF by AI, so it may have mistakes. The PDF is the original.

Daffodil International University Department of Electrical and Electronic Engineering Faculty of Engineering Final Examination, Summer - 2026 Course Code: 0714-211 Course Title: Electronics I Section: A, B, C, D, E, F, G Level-Term: L2-T1 Teacher's Initial: SD, KNA, KAH, MH Full Marks: 40 Exam Date: August 27, 2025 Time: 2.0 Hours [Q1 and Q2 are mandatory; Answer any three (03) from questions Q3, Q4, Q5, Q6.] [The second right most column indicates the COs with respective Bloom's level.] [The right most column indicates the assigned marks.] [All the symbols carry their usual meaning.] Q1. (a) Write the names of BJT modes of operation and mention the biasing conditions of the junctions for each of the operating modes. CO1, C1 [2] (b) For a BJT, show that beta = alpha / (1 - alpha). CO1, C2 [2] (c) Explain the operation of an n-channel MOSFET with necessary diagrams. CO1, C2 [4] Q2. For the circuit of Fig. Q2, (i) Calculate the value of R_C if the collector voltage is 3.4V at dc operating point, (ii) Draw the small signal equivalent circuit; (iii) Derive the expressions and find values for Z_i, Z_o and A_v. CO2, C3 [8] [Figure: A BJT amplifier circuit with V_CC = 12V, R_B = 400kΩ, R_C, R_E = 4kΩ, C_C1, C_C2, C_E, V_C = 3.4V, beta = 120, r_o = 50kΩ, input v_i, output v_o, input impedance Z_i, and output impedance Z_o] Q3. Given that V_B=4V for the following circuit of Fig. Q3, determine (i) V_E, (ii) V_C, (iii) beta. CO2, C3 [8] [Figure: A BJT biasing circuit with V_CC = 30V, R_{F1} = 330kΩ, R_{F2} = 220kΩ, R_C = 8.2kΩ, R_E = 1.8kΩ, capacitors 10uF, 5uF, 5uF, and V_B = 4V] Q4. Given the device characteristics in Fig. Q4(b), determine R_1, R_2, R_C and I_Csat for the circuit in Fig Q4(a). Assume beta = 150. CO2, C3 [8] [Figure: (a) A voltage-divider biased BJT circuit with V_CC = 24V, R_1, R_2, R_C, R_E = 1.2kΩ. (b) A graph of I_C (mA) versus V_CE showing Q-point at I_C = 4mA, V_CE = 12V] Q5. It is required to design the following circuit for biasing a MOS Amplifier. The design requirements are V_DD = 5V, I_D = 0.32mA, V_S = 1.6V, V_D = 3.4V with a 1uA current through R_{G1} and R_{G2}. Assume V_t = 1V and k'_n(W/L) = 1 mA/V^2. Determine the values of all the resistances in the circuit. CO2, C3 [8] [Figure: A MOSFET biasing circuit with V_DD, R_{G1}, R_{G2}, R_D, R_S] Q6. (a) Draw the small-signal ac equivalent circuit for the following Common-Source (CS) amplifier. CO2, C2 [4] [Figure: A Common-Source MOSFET amplifier circuit with V_DD, -V_SS, R_{sig}, C_{C1}, C_{C2}, R_D, R_S, C_S, R_G, R_i, v_{sig}, v_o] (b) The MOSFET in the following circuit of Fig. Q6(b) has V_t = 1V, k'_n(W/L) = 0.4mA/V^2 and lambda = 0. Determine the drain voltage. CO2, C3 [4] [Figure: A MOSFET circuit with V_DD = +5V, R_D = 1kΩ, output V_D]