Skip to content

Electrical Circuits II

EEE · Final · Spring 26

Paper 1 of 3By Md. Golam Murshed HridoySwitch

Paper 1 of 3

This browser can’t show the PDF here

Open it, and your phone’s PDF viewer takes it, or download it.

Read the questions as text

Read off the PDF by AI, so it may have mistakes. The PDF is the original.

Daffodil International University Department of Electrical and Electronic Engineering Faculty of Engineering Final Examination, Spring-2026 Course Code: 0713-121 Course Title: Electrical Circuits II Section: A, B, C, D, E, F, G Level-Term: L1-T2 Teacher's Initial: MSA, KMT, KNA Full Marks: 40 Exam Date: April 25, 2026 Time: 2 Hours Question no. 1 is COMPULSORY. Answer ANY FOUR from the remaining Questions. Q1. The switch in the circuit of Fig. 1 closes at t = 0, after being open for a long time. Calculate the transient current i_3(t), if V_s = 120 sqrt(2) sin(100 pi t + 30 degree) V. [Figure: A circuit diagram with a voltage source Vs, resistors R1, R2, R3, and an inductor L1] Q2. The energy stored in the coupled inductors of the circuit diagram shown in Fig. 2 is given by (1/2) L_1 i_1^2 + (1/2) L_2 i_2^2 - M i_1 i_2. Derive an expression for the maximum possible value of M from the limiting value of the energy, and define coupling coefficient (k) from your derived expression. What is the range of coupling coefficient? [Figure: A circuit diagram of two coupled inductors L1 and L2 with mutual inductance M] Q3. Explain mathematically what type of filter the circuit in Fig. 3 works as. Illustrate the ideal and actual frequency response of the corresponding filter, labeling important point(s). [Figure: A series RLC filter circuit with an inductor L, resistor R, and capacitor C connected across a voltage source v_i(t) and output voltage v_o(t)] Q4. (a) In a parallel RLC resonance circuit, R = 8 k ohm, L = 0.2 mH, C = 8 microF. Calculate omega_0, B, Q, omega_1, and omega_2. (b) A designer has to design a bandstop filter that will reject a 200 Hz sinusoid while allowing other frequencies to pass. The required bandwidth of the filter is 100 Hz, and the only available resistor has a value of 150 ohm. Draw a suitable circuit that can achieve the required specification using passive components (L and C), and determine the values of all necessary components required for the design. Q5. (a) For the Delta-Delta circuit in Fig. 5, determine the phase currents, line currents, and total power absorbed by the load. [Figure: A three-phase Delta-Delta connected circuit with balanced voltage sources and load impedances] (b) A three-phase Y-connected motor draws 5.6 kW when the line voltage is 220 V and the line current is 18.2 A. Determine the power factor, reactive power, and complex power absorbed by the motor. Q6. Determine the currents i_1 and i_2 in the circuit of Fig. 6. Calculate the energy stored in the coupled coils at time t = 1s, if v_s = 120 cos(10 t) V. [Figure: A circuit diagram with coupled coils of 0.5 H, 1 H, and mutual inductance 0.2 H, along with a 25 mF capacitor, 5 ohm resistor, and voltage source v_s] Q7. The unbalanced Delta-load of Fig. 7 is supplied by balanced line-to-line voltages of 240 V in the positive sequence. [Figure: An unbalanced Delta-load circuit connected to a three-phase supply lines A, B, and C with impedances 10 ohm, -j15 ohm, 8 ohm, j6 ohm, and 16 ohm] (a) Find the line currents I_a, I_b, and I_c. (b) Compute the total power absorbed by the load.