Electrical Circuits II
EEE · Final · Spring 26
Paper 2 of 3By Tayashuk Imam HossainSwitch
Paper 2 of 3
Read the questions as text
Read off the PDF by AI, so it may have mistakes. The PDF is the original.
Daffodil International University
Department of Electrical and Electronic Engineering
Faculty of Engineering
Final Examination, Spring-2026
Course Code: 0713-121
Course Title: Electrical Circuits II
Teacher's Initial: MSA, KMT, KNA
Section: A, B, C, D, E, F, G
Level-Term: L1-T2
Full Marks: 40
Exam Date: April 25, 2026
Time: 2 Hours
Question no. 1 is COMPULSORY. Answer ANY FOUR from the remaining Questions.
Q1. The switch in the circuit of Fig. 1 closes at t = 0, after being open for a long time. Calculate the transient current i_3(t), if V_s = 120sqrt(2) sin(100pi t + 30^\circ) V. CO-3 C(3) 8
[Figure: A circuit diagram with a voltage source Vs in series with resistor R1 (10 ohm), connected to a parallel combination of resistor R2 (10 ohm) and an inductor L1 (10 mH) in series with a switch, and another resistor R3 (10 ohm).]
Q2. The energy stored in the coupled inductors of the circuit diagram shown in Fig. 2 is given by 1/2 L1 i_1^2 + 1/2 L2 i_2^2 - M i_1 i_2. Derive an expression for the maximum possible value of M from the limiting value of the energy, and define coupling coefficient (k) from your derived expression. What is the range of coupling coefficient? CO-2 C(2) 8
[Figure: A diagram of two magnetically coupled inductors L1 and L2 with currents i1 and i2, and terminals marked with dots.]
Q3. Explain mathematically what type of filter the circuit in Fig. 3 works as. Illustrate the ideal and actual frequency response of the corresponding filter, labeling important point(s). CO-2 C(2) 8
[Figure: A circuit diagram with an AC voltage source v_i(t) in parallel with an inductor L, a resistor R, and a capacitor C measuring output voltage v_o(t).]
Q4. (a) In a parallel RLC resonance circuit, R = 8 k ohm, L = 0.2 mH, C = 8 mu F. Calculate omega_0, B, Q, omega_1, and omega_2. CO-2 C(3) 4
(b) A designer has to design a bandstop filter that will reject a 200 Hz sinusoid while allowing other frequencies to pass. The required bandwidth of the filter is 100 Hz, and the only available resistor has a value of 150 ohm. Draw a suitable circuit that can achieve the required specification using passive components (L and C), and determine the values of all necessary components required for the design. 4
Q5. (a) For the Delta-Delta circuit in Fig. 5, determine the phase currents, line currents, and total power absorbed by the load. CO-2 C(3) 4
[Figure: A Delta-Delta connected three-phase circuit with voltage sources and load impedances of 30 ohm and j10 ohm.]
(b) A three-phase Y-connected motor draws 5.6 kW when the line voltage is 220 V and the line current is 18.2 A. Determine the power factor, reactive power, and complex power absorbed by the motor. 4
Q6. Determine the currents i_1, and i_2 in the circuit of Fig. 6. Calculate the energy stored in the coupled coils at time t = 1s, if v_s = 120 cos(10 t) V. CO-2 C(3) 8
[Figure: A circuit diagram with a voltage source v_s, coupled coils with inductances 0.5 H and 1 H, mutual inductance, a capacitor of 25 mF, and a resistor of 5 ohm.]
Q7. The unbalanced Delta-load of Fig. 7 is supplied by balanced line-to-line voltages of 240 V in the positive sequence. CO-2 C(3) 8
[Figure: A Delta-connected unbalanced load with impedances 10 ohm, 8 ohm, -j15 ohm, j6 ohm, and 16 ohm connected to lines A, B, C.]
(a) Find the line currents I_a, I_b, and I_c.
(b) Compute the total power absorbed by the load.