Skip to content

Electrical Circuits II

EEE · Quiz · Spring 26

This browser can’t show the PDF here

Open it, and your phone’s PDF viewer takes it, or download it.

Read the questions as text

Read off the PDF by AI, so it may have mistakes. The PDF is the original.

Quiz - 01 Electrical Circuits II [0713-121] Full Marks: 15 Time: 15 Minutes ID: Section: Q1. Calculate I of the following circuit. (10) [Figure: Circuit diagram showing a 12 V AC/DC source connected to resistors R1 = 2 kΩ, R2 = 4 kΩ, inductor L2 = 3 mH in series-parallel with an inductor L3 = 4.7 mH, capacitor C3 = 3.3 µF, and resistor R3 = 4 kΩ] Q2. In a series RLC circuit, the source voltage is given by v(t) = 20 cos(wt), where w = 10^3 rad/s, the resistance R = 400 Ω, the capacitance C = 200 µF. If the current flowing through the circuit is given by i(t) = 35.58 cos(wt - 44.64°) mA, find the value of the inductance (L). (05) Quiz - 01 Electrical Circuits II [0713-121] Full Marks: 15 Time: 15 Minutes ID: Section: Q1. Find the equivalent impedance of the following circuit. (10) [Figure: Circuit diagram showing Zeq connected to a bridge network of components: 1+j3 Ω, 1-j1 Ω, 1+j2 Ω, and j5 Ω] Q2. In a series circuit containing a 100 Ω resistor and an unknown capacitor, the voltage across the resistor and the capacitor are equal in magnitude. If the frequency is 60 Hz, calculate the capacitance C. (05) Quiz - 01 Electrical Circuits II [0713-121] Full Marks: 15 Time: 15 Minutes ID: Section: Q1. Determine the equivalent impedance of the following circuit, when w = 10^3 rad/s. (10) [Figure: Circuit diagram with Zeq, resistors R1 = 2 kΩ, R2 = 2 kΩ, inductors L1 = 4.7 mH, L2 = 1 µH, and capacitors C1 = 1 nF, C2 = 3.3 µF] Q2. A branch has Z1 = 10 + j10 Ω. If you want to add a parallel capacitor Xc such that the total impedance is purely real, what must be the value of Xc? (05) Quiz - 03 Electrical Circuits II [0713-121] Full Marks: 15 Time: 20 Minutes ID: Section: Q1. The circuit diagram in Fig. 1 represents a balanced 3-phase Y-Y system. Find the line current, and the average power delivered to the load. [Here, ZLoad = 9 + j12 Ω, and Zline = 1 + j2 Ω] (07) [Figure: Fig. 1 showing a 3-phase Y-Y system with sources 208∠0° V, 208∠240° V, 208∠120° V, line impedances, and load impedances] Q2. Two balanced loads are connected in parallel to a 13.8 kV (rms) line. Load 1 draws 500 kW at 0.7 lagging pf. Load 2 draws 300 kVAR at 0.9 lagging pf. Determine the total complex power and the overall power factor. (08) Quiz - 04 Electrical Circuits II [0713-121] Full Marks: 15 Time: 20 Minutes ID: Section: Q1. (08) [Figure: Fig. 1 showing a coupled inductor circuit with source 12 cos 4t V, resistor 2 Ω, inductors 4 H and 2 H with mutual inductance 1 H, capacitor 1/4 F, and resistor 1 Ω with voltage vo] (a) Find the coupling coefficient. (b) Calculate vo. (c) Determine the energy stored in the coupled inductors at t = 2 s. Q2. Design a bandstop filter that will reject a 200 Hz sinusoid while passing other frequencies. The required bandwidth is 100 Hz, and the only available resistor has a value of 150 Ω. (07) Quiz - 04 Electrical Circuits II [0713-121] Full Marks: 15 Time: 20 Minutes ID: Section: Q1. (08) [Figure: Fig. 1 showing a coupled inductor circuit with source 16cos(4t + 30°) V, resistor 2 Ω, inductor j4 Ω, mutual inductor j1 Ω, capacitor -j1 Ω, resistor 2 Ω, voltage Vx, and current source 4cos(4t) A] (a) Find the coupling coefficient. (b) Calculate Vx. (c) Determine the energy stored in the coupled inductors at t = 2 s. Q2. Design a bandpass filter with two half-power frequencies given by w1 = 20.1 kHz, and w2 = 20.3 kHz respectively. The only available resistor has a value of 20 kΩ. Determine the value of L, C. (07)