Electrical Circuits II
EEE · Quiz · Spring 26
Read the questions as text
Read off the PDF by AI, so it may have mistakes. The PDF is the original.
Quiz - 01
Electrical Circuits II [0713-121]
Full Marks: 15
Time: 15 Minutes
ID:
Section:
Q1. Calculate I of the following circuit. (10)
[Figure: Circuit diagram showing a 12 V AC/DC source connected to resistors R1 = 2 kΩ, R2 = 4 kΩ, inductor L2 = 3 mH in series-parallel with an inductor L3 = 4.7 mH, capacitor C3 = 3.3 µF, and resistor R3 = 4 kΩ]
Q2. In a series RLC circuit, the source voltage is given by v(t) = 20 cos(wt), where w = 10^3 rad/s, the resistance R = 400 Ω, the capacitance C = 200 µF. If the current flowing through the circuit is given by i(t) = 35.58 cos(wt - 44.64°) mA, find the value of the inductance (L). (05)
Quiz - 01
Electrical Circuits II [0713-121]
Full Marks: 15
Time: 15 Minutes
ID:
Section:
Q1. Find the equivalent impedance of the following circuit. (10)
[Figure: Circuit diagram showing Zeq connected to a bridge network of components: 1+j3 Ω, 1-j1 Ω, 1+j2 Ω, and j5 Ω]
Q2. In a series circuit containing a 100 Ω resistor and an unknown capacitor, the voltage across the resistor and the capacitor are equal in magnitude. If the frequency is 60 Hz, calculate the capacitance C. (05)
Quiz - 01
Electrical Circuits II [0713-121]
Full Marks: 15
Time: 15 Minutes
ID:
Section:
Q1. Determine the equivalent impedance of the following circuit, when w = 10^3 rad/s. (10)
[Figure: Circuit diagram with Zeq, resistors R1 = 2 kΩ, R2 = 2 kΩ, inductors L1 = 4.7 mH, L2 = 1 µH, and capacitors C1 = 1 nF, C2 = 3.3 µF]
Q2. A branch has Z1 = 10 + j10 Ω. If you want to add a parallel capacitor Xc such that the total impedance is purely real, what must be the value of Xc? (05)
Quiz - 03
Electrical Circuits II [0713-121]
Full Marks: 15
Time: 20 Minutes
ID:
Section:
Q1. The circuit diagram in Fig. 1 represents a balanced 3-phase Y-Y system. Find the line current, and the average power delivered to the load. [Here, ZLoad = 9 + j12 Ω, and Zline = 1 + j2 Ω] (07)
[Figure: Fig. 1 showing a 3-phase Y-Y system with sources 208∠0° V, 208∠240° V, 208∠120° V, line impedances, and load impedances]
Q2. Two balanced loads are connected in parallel to a 13.8 kV (rms) line. Load 1 draws 500 kW at 0.7 lagging pf. Load 2 draws 300 kVAR at 0.9 lagging pf. Determine the total complex power and the overall power factor. (08)
Quiz - 04
Electrical Circuits II [0713-121]
Full Marks: 15
Time: 20 Minutes
ID:
Section:
Q1. (08)
[Figure: Fig. 1 showing a coupled inductor circuit with source 12 cos 4t V, resistor 2 Ω, inductors 4 H and 2 H with mutual inductance 1 H, capacitor 1/4 F, and resistor 1 Ω with voltage vo]
(a) Find the coupling coefficient.
(b) Calculate vo.
(c) Determine the energy stored in the coupled inductors at t = 2 s.
Q2. Design a bandstop filter that will reject a 200 Hz sinusoid while passing other frequencies. The required bandwidth is 100 Hz, and the only available resistor has a value of 150 Ω. (07)
Quiz - 04
Electrical Circuits II [0713-121]
Full Marks: 15
Time: 20 Minutes
ID:
Section:
Q1. (08)
[Figure: Fig. 1 showing a coupled inductor circuit with source 16cos(4t + 30°) V, resistor 2 Ω, inductor j4 Ω, mutual inductor j1 Ω, capacitor -j1 Ω, resistor 2 Ω, voltage Vx, and current source 4cos(4t) A]
(a) Find the coupling coefficient.
(b) Calculate Vx.
(c) Determine the energy stored in the coupled inductors at t = 2 s.
Q2. Design a bandpass filter with two half-power frequencies given by w1 = 20.1 kHz, and w2 = 20.3 kHz respectively. The only available resistor has a value of 20 kΩ. Determine the value of L, C. (07)