Skip to content

Electronics II

EEE · Final · Summer 26

Paper 1 of 2Section A · Batch 251Switch

Section A · Batch 251

Paper 1 of 2

This browser can’t show the PDF here

Open it, and your phone’s PDF viewer takes it, or download it.

Read the questions as text

Read off the PDF by AI, so it may have mistakes. The PDF is the original.

Daffodil International University Department of Electrical and Electronic Engineering, Faculty of Engineering Final Examination, Summer-2026 Course Code: 0714-221 | Course Title: Electronics II Section: A, B, C, D | Level-Term: L2-T2 | Teacher's Initial: SR, MH Full Marks: 40 | Date: 27-Aug., 2026 | Time: 2.00 Hours [Notes: Answer all the following questions] [The second right most column indicates the course outcomes with respective Bloom's level and right most column indicates the allocated marks] Q1. A series-tuned antenna circuit consists of a variable capacitor (60 pF to 380 pF) and a 200-uH antenna coil that has a dc resistance of 10 ohm. | CO-3 C5 | 04 - Find the frequency range of radio signals to which the radio is tunable. - Determine the value of Quality Factor, Q at each end of the frequency range Q2. A biomedical signal acquisition system needs to pass only a specific frequency band of interest and suppress all other frequencies. The design requires a first-order active band-pass filter formed by cascading first-order high-pass and low-pass stages. | CO-3 C5 | 04 Design specifications: - Lower cutoff frequency: 100 Hz - Upper cutoff frequency: 1 kHz - Overall gain: 20 - Select capacitor values: High-pass stage: 0.3 uF & Low-pass stage: 0.01 uF Determine: a. Resistor values for both stages b. The center frequency and bandwidth c. Design the final band pass filter circuit for the required specifications. Q3. (i) Explain the working principle of 555 timer in astable mode. | CO-3 C2 | 04 (ii) Design a multivibrator with 555 timer in astable mode which produces a square wave of 2 MHz and duty cycle will be 60%. | CO-3 C5 | 04 Q4. (i) Explain, with mathematics and graphical illustration, how positive feedback enables an oscillator to produce an undamped sinusoidal oscillation without any external input, explain based on the Barkhausen criterion. | CO-3 C2 | 04 (ii) Explain the circuit operation of Colpitts Oscillator. Focus how feedback circuit can produce a phase shift of 180 degree and show the frequency of oscillation and feedback fraction. | CO-3 C2 | 04 (iii) Design a Hartley oscillator to produce a sine wave of frequency 96 MHz. use Capacitors of LC tank circuit C=12 pF. And consider the feedback fraction m_v=0.1 (Find the parameter values and Draw the Complete Designed Circuit) | CO-3 C4 | 04 Q5. Analyze and find the transfer function and pass band gain (as a function corner frequency of low pass and high pass filter) of the below filter circuit given in Fig. 1. What kind of filter is it? | CO-3 C4 | 04 [Figure: Active band-pass filter circuit with operational amplifiers, resistors R, R_f, and capacitors C_1, C_2, labeled Fig. 1] (i) Analyze that the Voltage gain with negative feedback of an amplifier is A_vf = A_v / (1 + A_v m_v) where the gain of the amplifier without feedback is A_v and feedback fraction is m_v. And Discuss the advantages of Negative Voltage Feedback. | CO-2 C4 | 04 (ii) An amplifier has a voltage amplification A_v and a fraction m_v of its output is feedback in opposition to the input. If m_v=0.1 and A_v=300, calculate the percentage change in the gain of the system if A_v falls 8 db due to ageing. | CO-2 C3 | 04