Electrical Circuits II
EEE · Final · Fall 23
Section A, B, C, D
Read the questions as text
Read off the PDF by AI, so it may have mistakes. The PDF is the original.
Daffodil International University
Department of Electrical and Electronic Engineering
Faculty of Engineering
Final Examination, Fall - 2023 (Day)
Course Code: 0713-121
Course Title: Electrical Circuits II
Teacher's Initial: MSA, KNN
Section: A, B, C, D
Level-Term: L1-T2
Time: 1.5 Hours
Full Marks: 25
Exam Date: September 23, 2023
Answer any five out of seven
Q.1 If vs(t) = 20 sin(100t - 40°) volt, find is(t) in the following figure Q.1.
[Figure: A circuit diagram showing a sinusoidal voltage source vs(t) connected in parallel with a 10 ohm resistor, a 0.2H inductor in series with a 30 ohm resistor, and a 0.5 mF capacitor. The current is(t) flows through the rightmost branch.]
CO-1 C(2) | 5
Q.2 Find the equivalent impedance Zeq(1) in the following figure Q.2(a) & Zeq(2) in figure Q.2(b).
[Figure: Q.2(a) shows a network with 8 ohm, -j6 ohm, 4 ohm, and j10 ohm impedances. Q.2(b) shows a network with -j2 ohm, 2 ohm, j4 ohm, j2 ohm, -j5 ohm, and other components.]
CO-1 C(2) | 5
Q.3 (a) Find the r.m.s. value of the full wave rectified voltage in figure Q.3(a).
(b) Calculate the phase shift angle by the RL circuit in figure Q.3(b).
[Figure: Q.3(a) is a graph of full-wave rectified voltage showing amplitude 10 over time t. Q.3(b) shows a series circuit with a -j5 ohm impedance, 5 ohm resistor, and voltage source Vi and Vo.]
CO-2 C(2) | 5
Q.4 (a) Determine io in the following figure Q.4, when DC voltage source is active only.
(b) Calculate the reactances when (1) v1 is active only, and (2) v2 is active only
[Figure: A circuit with a 1 ohm resistor, 1/6 F capacitor, 24V DC source, 2H inductor, 2 ohm resistor, v1 = 10sin(t-30°)V, is = 2cos3t, and a 4 ohm resistor with io.]
CO-2 C(3) | 5
Q.5 Calculate Io in the following circuit using (a) Norton's theorem, and (b) Thevenin's theorem.
[Figure: A bridge-like circuit with 40∠0° voltage source, 8 ohm resistor, -j2 ohm capacitor, 10 ohm resistors, j4 ohm inductor, j5 ohm inductor, and Io.]
CO-2 C(3) | 5
Q.6 (a) Obtain the nodal equations for the following figure Q.6(a).
(b) Obtain the equation for the super mesh in the following figure Q.6(b).
[Figure: Q.6(a) shows a circuit with 4 ohm, j4 ohm, 4∠60° current source, -j10 ohm, 2 ohm resistors. Q.6(b) shows a complex mesh circuit with multiple sources and resistors.]
CO-2 C(3) | 5
Q.7 (a) Using current divider rule, calculate Io in the following figure Q.7.
(b) Using concept of source theorem, calculate also Io.
[Figure: A circuit with a 20∠15° current source, 60 ohm resistor, -j25 ohm capacitor, j20 ohm inductor, and Io through the j20 ohm branch.]
CO-2 C(3) | 5