Energy Conversion I
EEE · Final · Spring 26
Section A, B, C, D
Read the questions as text
Read off the PDF by AI, so it may have mistakes. The PDF is the original.
Daffodil International University
Department of Electrical and Electronic Engineering
Faculty of Engineering
Final Term Examination, Spring 2026
Course Code: 0713-213
Course Title: Energy Conversion I
Section: A, B, C, D
Level-Term: L2 - T1
Teacher's Initial: DRA, PA
Full Marks: 40
Exam Date: April 25, 2026
Time: 2.0 Hours
Attempt to Answer all of the 4 Questions
The second right most column indicates the course outcomes with respective Bloom's level and right most column indicates the allocated marks
Q1. a) Explain in your own words any two of the following:
Auto-Transformer, Single-Phase Induction Motor, Induction Generator, Parallel Operation of Transformers.
CO-2 [4]
C(2)
Q1. b) A 4-pole, 50-Hz, 3-phase induction motor develops a maximum torque of 60.8 Nm at 1375 rpm. The resistance of the star-connected rotor is 0.15 ohm/phase. Calculate the value of the resistance that must be inserted in series with each rotor phase to produce a starting torque equal to 3/4th of the maximum torque.
CO-2 [4]
C(4)
Q2. a) Show that a transformer achieves maximum efficiency when copper losses are equal to iron losses.
CO-2 [3]
C(2)
Q2. b) A 5.6 kVA, 50 Hz, 250/400 V single-phase transformer undergoes open-circuit and short-circuit tests with the following test data:
Open-circuit test: Voltage = 250 V, Current = .5 A, Power = 80 W - on LV side
Short-circuit test: Voltage = 20 V, Current = 20 A, Power = 50 W - HV shorted
Calculate (i) equivalent circuit parameters w. r. to LV side, (ii) efficiency and (iii) terminal voltage on the HV side when it supplies 1/4th of full load with a 0.8 power factor lagging, the supply voltage being 250 V.
CO-2 [6]
C(4)
Q3. a) Prove that maximum starting torque is achieved when rotor resistance is equal to rotor reactance.
CO-2 [3]
C(2)
Q3. b) 3-phase induction motor having a 6-pole, star-connected stator winding runs on 250 V, 50-Hz supply. The rotor resistance and standstill reactance are 0.12 ohm and 0.85 ohm per phase. The ratio of stator to rotor turns is 1.8. Full load slip is 4%. Calculate the developed torque at full load, maximum torque and speed at maximum torque.
CO-2 [6]
C(4)
Answer any 2 (Two) from the following 3 (Three) questions:
Q4. a) A 230-V, 3-phase, 4-pole, 50-Hz, Y-connected induction motor is rated 3.8 kW. The equivalent circuit parameters are: R1 = 0 ohm, X1 = 0.8 ohm, R2' = 0.45 ohm, X2' = 1.2 ohm, Xm = 30 ohm. The stator core loss is 60 W and rotational loss is 140 W. For a slip of 0.04, compute: (i) input current, (ii) air-gap power, P2 (iii) mechanical power, Pm (iv) gross torque, Tg (v) output power, Pout and (vi) efficiency, n.
CO-3 [7]
C(5)
Q4. b) A 120V, 60-Hz, 3-phase, Y-Connected, 6-pole induction motor has an equivalent T-circuit consisting of stator impedance of 0.07 + j 0.3 ohm and an equivalent rotor impedance at standstill of (0.08 + j 0.3) ohm. Magnetizing branch has Xm = 6.33 ohm, R0 = 45.45 ohm. Determine (a) rotor current, I2' (b) stator current, I1 (c) primary p.f. (d) gross power output, Pg (e) gross torque, Tg (f) input power, P1 and (g) gross efficiency by using approximate equivalent circuit. Assume a slip of 2%.
CO-3 [7]
C(5)
Q4. c) A 10-kVA distribution transformer has a full-load efficiency at unity p.f. of 98%, the copper and iron losses then being equal. Calculate its all-day efficiency if it is loaded throughout the 24 hours as follows: One-fourth load for 10 hours; Quarter load for 3 hours; Half load for 6 hours; and Full load for 5 hours. Assume load p.f. of unity.
CO-3 [7]
C(5)