Skip to content

Electrical Circuits II

EEE · Final · Summer 26

Paper 1 of 2By PritomSwitch

Paper 1 of 2

This browser can’t show the PDF here

Open it, and your phone’s PDF viewer takes it, or download it.

Read the questions as text

Read off the PDF by AI, so it may have mistakes. The PDF is the original.

Daffodil International University Department of Electrical and Electronic Engineering Faculty of Engineering Final Examination, Summer-2026 Course Code: 0713-121 Course Title: Electrical Circuits II Teacher's Initial: MSA, KNA Section: A, B Level-Term: L1-T2 Time: 2 Hours Exam Date: August 23, 2026 Full Marks: 40 Question no. 1 is COMPULSORY. Answer ANY FOUR from the remaining Questions. Q1. The switch in the circuit of Fig. 1 closes at t = 0, after being open for a long time. Calculate the transient current i3(t), if Vs = 120sqrt(2) sin(100pi t + 30) V. [Figure: A circuit diagram showing an AC voltage source Vs in series with a resistor R1 (10 ohms), and a parallel combination of R2 (10 ohms), C (250 uF), and a switch in series with R3 (10 ohms).] Q2. The energy stored in the coupled inductors of the circuit diagram shown in Fig. 2 is given by (1/2) L1 i1^2 + (1/2) L2 i2^2 - M i1 i2. Derive an expression for the maximum possible value of M from the limiting value of the energy, and define coupling coefficient (k) from your derived expression. What is the range of coupling coefficient? [Figure: A circuit diagram of mutually coupled inductors L1 and L2 with mutual inductance M.] Q3. Explain mathematically what type of filter the circuit in Fig. 3 works as. Illustrate the ideal and actual frequency response of this filter, labeling important point(s). [Figure: An RL low-pass or high-pass filter circuit with Vin, resistor R, inductor L, and Vout.] Q4. (a) Resonant frequency and quality factor of a RLC series resonant circuit is 10 rad/s and 20, respectively. Determine R, L, and C. Also, determine the amplitude of the currents at w0 and w1, w2. (b) A parallel resonant circuit has R = 100 kohm, L = 20 mH, and C = 5 nF. Calculate w0 and w1, w2, Q and B. Q5. (a) For the Y-Delta circuit in Fig. 5(a), determine the line currents, and average power delivered to the load. [Figure: A balanced or unbalanced three-phase Y-Delta circuit with source voltages 220 V at 0°, -120°, and 120°, line impedances 2 ohms, and delta load impedances (9 - j6) ohms.] (b) A three-phase Delta-connected motor draws 10 kVA at a power factor of 0.8 lagging. If the three-phase system has an effective line voltage of 400 V with abc phase sequence, find the line current. Q6. Determine the currents i1, and i2 in the circuit of Fig. 6. Calculate the energy stored in the coupled coils at time t = 1s, if vs = 120 cos 10t V. [Figure: A coupled inductor circuit with inductances 0.5 H, 1 H, 0.2 H, a 25 mF capacitor, and a 5 ohm resistor driven by a voltage source vs.] Q7. The unbalanced Delta-load of Fig. 7 is supplied by balanced line-to-line voltages of 230 V in the positive sequence. Find: (i) the line currents Ia, Ib, Ic, and (ii) the total power absorbed by the load. [Figure: An unbalanced Delta-load with branch impedances 10 ohms, (8 - j5) ohms, 16 ohms, and (6 + j6) ohms connected to lines Ia, Ib, Ic.]